Select Page

egg profil joint tester – multi-part

egg profil joint tester – multi-part

The pipe joint tester for egg-shaped profiles includes several parts and allow disassembly of the inspection unit into 2 or 3 components This way, it can be introduced through a manhole as well. At the installation site, the pipe joint tester requires just a few steps to reassemble.

The carriage helps to center the pipe joint tester in the inspection area; the two extra-wide hollow chamber profiles located at both sides of the pipe sleeve are pressurized by means of a foot operated air pump or another generator of pressurized air with a pressure of 4 to 6 bar to seal the test chamber hermetically.

In case of a water leakage test, keep the bleeding valve open and fill test chamber with water until water exits from the bleeding valve. Then close the bleeding valve, wait for the indication of the test pressure selected and close the inlet valve as well to start the test. To perform the air pressure test, the test pressure required is generated in the test chamber.

Characteristics

  • to perform leak tests of egg-shaped profile pipe connections with air or water acc. to standard EN 1610 and other test standards
  • the construction in several parts allows an introduction through manholes for later installation on site
  • it is a rugged welded steelwork of several parts with 2 hollow rubber chamber profiles and undercarriage
  • incl. Adaptor quick connectors type 26 (tire valve) and adaptor Geka coupling of air plug coupling
  • with 1/2″ Geka testconnector

 

Other sizes and segmentations available at request.

Ordering Information

Art.-Nr.
Produktbezeichnung
Eigenschaften
LxBxH & Gewicht
 

Art.-Nr.:
2001830
in Ei-Profile: 300/450
Aufbau: 1 component
Betriebsüberdruck: 6 bar (87 psi)
Maße: 600 × 420 × 270 mm
Gewicht:


Art.-Nr.:
2001831
in Ei-Profile: 350/525
Aufbau: 1 component
Betriebsüberdruck: 6 bar (87 psi)
Maße: 600 × 495 × 320 mm
Gewicht:


Art.-Nr.:
2001832
in Ei-Profile: 400/600
Aufbau: 1 component
Betriebsüberdruck: 6 bar (87 psi)
Maße: 600 × 570 × 370 mm
Gewicht:


Art.-Nr.:
2001833
in Ei-Profile: 500/750
Aufbau: 1 component
Betriebsüberdruck: 6 bar (87 psi)
Maße: 600 × 730 × 470 mm
Gewicht:


Art.-Nr.:
2001835
in Ei-Profile: 600/900
Aufbau: 2 components
Betriebsüberdruck: 6 bar (87 psi)
Maße: 600 × 870 × 570 mm
Gewicht:


Art.-Nr.:
2001836
in Ei-Profile: 700/1050
Aufbau: 2 components
Betriebsüberdruck: 6 bar (87 psi)
Maße: 600 × 1020 × 670 mm
Gewicht:


Art.-Nr.:
2001837
in Ei-Profile: 800/1200
Aufbau: 2 components
Betriebsüberdruck: 6 bar (87 psi)
Maße: 600 × 1170 × 770 mm
Gewicht:


Art.-Nr.:
2001840
in Ei-Profile: 900/1350 mm
Aufbau: 3 components
Betriebsüberdruck: 6 bar (87 psi)
Maße: 600 × 1320 × 870 mm
Gewicht:


Art.-Nr.:
2001841
in Ei-Profile: 1000/1500
Aufbau: 3 components
Betriebsüberdruck: 6 bar (87 psi)
Maße: 600 × 1470 × 970 mm
Gewicht:


Art.-Nr.:
2001842
in Ei-Profile: 1200/1800
Aufbau: 3 components
Betriebsüberdruck: 6 bar (87 psi)
Maße: 600 × 1770 × 1170 mm
Gewicht:


Art.-Nr.:
2001843
in Ei-Profile: 1300/1950
Aufbau: 3 components
Betriebsüberdruck: 6 bar (87 psi)
Maße: 600 × 1920 × 1270 mm
Gewicht:


Art.-Nr.:
2001844
in Ei-Profile: 1400/2100
Aufbau: 3 components
Betriebsüberdruck: 6 bar (87 psi)
Maße: 600 × 2070 × 1370 mm
Gewicht:


Art.-Nr.:
2001845
in Ei-Profile: 1600/2400
Aufbau: 3 components
Betriebsüberdruck: 6 bar (87 psi)
Maße: 600 × 2370 × 1570 mm
Gewicht:


Click here to go to the product.

You have Successfully Subscribed!

0
Request for quotation